• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet to leave and come back at their own pace, without needing to let them in or out. They also can help stop your cat from peeing in the house.

Installing a cat flap on the door panel made of upvc is much simpler than installing one in glass doors, however it requires some knowledge and the appropriate tools.

Measure the Door

The installation of a cat flap inside the door isn't easy but if you select the right kind of cat flap be patient and follow the instructions provided it should not prove to be too much trouble. We will be showing how to trace the shape, using an jigsaw for cutting out the door's opening and then finish off the job by fixing the cat flap to the door. This will ensure that the flap remains in place and protects the door from wind and rain which can cause damage.

To determine the size of the cat flap you need, measure your pet's width. This will allow you to select a flap that is big enough to allow your pet to go into the house and leave without having to open the door each time.

Once you have the measurements you can determine where on the door the template should be positioned, usually this is done with an X, but some kits come with a drawing that shows the location to drill, if yours does, then you can stick it to the door and draw a line around the door. If your door has a sill or moulding along the bottom edge ensure that you have enough space to ensure your cat flap installation near me's safety and stop them from gaining access to your home.

Set a square to check that you're cutting correctly and ensure that the hole is a good rectangle shape. When you are satisfied with this, you can begin to remove the remaining door material. If you have an already-cut square, use it to ensure that you are cutting correctly and also to ensure that the hole is a proper rectangle. Once you are satisfied with the shape, you can begin to take off the remaining door material.

Draw a Line

The cat flap lets you to let your pet in and outside without having to worry about unwanted visitors or unwanted gifts. It also stops draughts and helps to keep your home's temperature in check. However, installing an animal flap on your door might seem like an intimidating task for those who haven't done it before, which is why many to hire an expert joiner or carpenter to complete the task. While this is definitely an option, it's possible to do the job yourself if you have the appropriate tools and follow the instructions carefully.

While this is far simpler when using a timber door it is still possible to do this in uPVC doors - although you should be careful not to scratch the doors since this could invalidate your warranty. First, you must examine the door's measurements to ensure it will accommodate the new cat-flap. If you have an ordinary uPVC panel it should be a breeze. However when your door is composite or a different type of door, you may have to be more cautious.

The next step is to determine the height of your cat's belly. This is the amount of height between the floor and the bottom of your cat's stomach. You will need to find an area on the door that allows your cat to pass through comfortably. Once you've figured out the measurements you'll have to mark the area using a spirit level and a pencil so that you know the opening will fit your cat.

After you have marked the area, you're now ready to cut the hole. You will need a jigsaw and it is crucial to be patient to ensure that the cuts are smooth and clean, rather than uneven and rough, as it could cause damage to your door. It is also important to wear safety glasses and a dust protection mask whenever working with the jigsaw as inhaling the sawdust could be hazardous to your health. After you've completed the cutting process, you will have to smooth out the edges of the hole with sandpaper so that your cat flap can be fitted easily in place.

Cut a Hole

The process of fitting a cat flap into an existing door panel or double glazing sealed unit is quite difficult. You may be tempted to tackle the task yourself, but unless have plenty of experience with DIY, it's recommended to hire an expert to complete the job for you. A botched job may not just be ugly, but also an issue for security as well as allowing cold air to enter when the cat is outside and hot air to escape when inside.

The hole's location should be marked on the door using a pencil and spirit level. This will ensure it is positioned correctly and is flush with the rest of the door. Make sure you have an sandpaper piece on ready to smooth any edges.

Once the line has been traced, you must cut the hole with the jigsaw. Remember to wear the appropriate safety equipment when working with the power tool. If you're worried about the noise, you can get a cordless jigsaw which is quieter and easier.

It is important that you only cut away the material needed to fit the cat flap. It is necessary to leave a bit of material for the wall thickness of the flap. However cutting away too much could cause problems or even damage the frame of the door.

A door made of upvc could have a metal frame or panel which could block the microchip cat flap, and if this is the case, you'll need to cut an over-sized hole to ensure that the metal does not come into contact with the the cat flap, if this is done, it is important to fill in the oversize gap and make it watertight.

If you are fitting a cat flap into a upvc door or double-glazed window with a frame made of metal, you'll need to speak to a specialist who can supply you with a new pane of glass with the hole for the cat flap premade in it. This is less expensive than fitting a cat flap inside an existing pane that was not made for this purpose.

Install the Flap

Cat flaps allow your pet to move around whenever they want, allowing them the ability to unwind inside the house when they want to. However, if you own an uPVC door, it might be difficult to install a cat flap, particularly in the absence of glass panes that can be cut to accommodate one. If you are willing to install a half-glazed uPVC replacement upvc door panels with cat flap panel, it's possible to add the cat flap. It's not as easy as simply making a hole in the door though and there are a few things you'll need first to make sure it's safe.

A composite, uPVC, or GRP door panel is typically made up of a plastic skin that is bonded to an insulating polystyrene core. The material is fairly fragile and care must be taken when cutting through it to avoid damaging. This type of door typically comes with a template drawing that you can use as a guide for cutting the hole in your door.

Once you have marked the location of the hole in your door, it's now time to put in the cat flap itself. You can purchase and install a wide variety of different models that range from simple push-button operated models to microchip-activated ones that allow access only to your pet. Whatever type of Cat Flap In Upvc Door Panel flap you pick, it's vital that your cat flap fitters can utilize the flap with ease without getting stuck outside in bad weather.

It is a good idea to choose circular fittings rather than a square one, as circles can be more securely cut into the door glass. It's because square holes are more likely to break the glass when they are drilled. This is also a safer choice since you don't have to drill into the toughened glass that could break and hurt your pet or family. This is particularly crucial if you have a young or elderly person at home who could be injured by shards of glass.