• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

It is a good idea for you to replace your locks when they start to exhibit signs that they're worn out. These signs include things like having difficulty turning the lock, or having a key that doesn't fit.

It is simple to set up new door hardware. You only need to follow these simple steps.

Deadbolt

The deadbolt is the main security for your door against forced entry. It is stronger and safer than the latch which activates the lock. Therefore, you'll be sure that the new deadbolt you purchase meets your requirements. If you can, select deadbolts made of case-hardened steel that does not have exposed screwheads on the outside to prevent unauthorized drilling. To ensure security, the interior side of your deadbolt should be drilled into the door frame.

When you install the deadbolt, check that your new deadbolt's bolt is extending smoothly into the strike plate after you lock and close the door. If it doesn't, use a wood chisel to mortise the bolt hole in the strike plate and install the deadbolt. Make sure that the doorknob's latch aligns with the hole in the deadbolt when you close and lock the door, too.

Before you install your new deadbolt, check that it is the same size of the old one. The majority of door locks come with an illustration of how high the bolt should be above the doorknob. However, it is always recommended to speak with an expert in hardware for advice if you're not sure what backset measurement you need for your doors. They'll be able to direct you to models that work with your door and deadbolt opening.

After ensuring that the new bolt assembly is the correct length, insert it into the hole in the door. Screw the faceplate of the latch into the hole if the new deadbolt is equipped with one. It is a good idea to fix the latch faceplate onto the frame with the screws recommended by experts, and also.

Some sets of locks come with a decorative or "dummy" bolt that allows you to install the keyed-deadbolt, while having an effective latch. If you're given the option that the dummy bolt is installed, it must be installed using the same screws that are used to mount the faceplate of the latch. This will give you the best security.

Some deadbolts are accessible only via a thumb-turn from inside, while others come with two cylinders that permit both keyed and unkeyed access. It's best to choose a lock that is commercial grade to ensure the highest security. They are tested to withstand 250,000 cycles of opening and closing before being sold to homeowners.

Latch

The latch is the component of the lock that retracts the bolt to open and close the door. It's typically held in place by screws that are located on the side of the lock, but it can also be attached to the strike plate or the inside of the door jamb. It is essential to replace the composite door replacement lock latch with the correct one for your existing hardware. You can either hold the latch up against your existing hardware or check the label on the replacement. Dunn Lumber carries a variety of brands, however it's best to stick with the same brand as your existing hardware to ensure you get an appropriate latch that fits properly.

Some doors have the appearance of a hasp, instead of a latch. A hasp is an elastic strap with a slot punched in it that is able to be positioned over the staple. The staple is then fixed to the door door frame using a nail. When the door is closed the strap pulls the staple down and secures it into position. A hasp is typically used in commercial buildings because it's less expensive than deadbolts.

Like any mechanism that has moving parts, a lock will wear out from repeated use over time. Sometimes, the internal mechanism can start to "stick" and become difficult to turn, requiring to replace the entire lockset. Sometimes, the handle or doorknob will break, making it necessary to replace it as well.

If your lock is sticking to the key, you can try putting some graphite inside the keyhole. You can either dust or squirt it on the key, and then turn the lock a couple of times to work in the graphite. You can also remove the knob with a screwdriver, which will expose all the parts and let you see what is going on inside the.

After taking the knobs off and tightening the two or three screws on the outside of the cylinder by turning them clockwise. The faceplate should be removed and replaced. Surface-mounted rim locks include an additional set of cylinder screws on the rear of the case. These must be removed, as well as the cover plate.

Strike Plate

The strike plate acts as a reinforcement and upgrade to the locking system. It is attached to the holes that are used for deadbolts or master key systems bolts. It helps keep intruders out by ensuring that the latch of the lock is secured in the plate when the bolt is engaged. A top-quality strikeplate can enhance the durability of locks as well as enhance security.

Standard strike plates are flat plates made of metal with a hole, or a series of holes, cut into them. It is anchored, typically using screws, to the frame of a doorway to give the latch a place to rest in when it is closed. The strike plate must be aligned precisely with the lockset to ensure maximum security against burglaries.

If the strike plate of a door is damaged, it must be replaced as soon as it is possible to ensure that the door can shut and latch properly. To replace a strikeplate, you must first ensure that it is aligned with the bolthole in the doorjamb. An easy way to accomplish this is to put a piece of tape in the bolt hole and then test the latch by closing and opening the door. If the latch does not catch, remove the tape and chisel the area so that the striker will be flush with the doorjamb.

After the area has been removed, it is important to use a larger screw to anchor the strike plate. They must be at least 3 inches long to ensure they are securely anchored into a stud that is behind the trim board. If you do not install the longer screws, the doorjamb's wood could split during a kickin attack by an burglar, making the door vulnerable.

A professional locksmith will quickly replace a damaged or worn out strike plate. They can also install new strike plates on doors that have never had them before. In addition, they can upgrade existing strike plates to enhance a building's security and improve appearance. This can help a property owner draw in tenants looking for a safe and secure living space and peace of mind.

Keys

The key cylinder of your lock is the part that allows the key to move pins so that the inside handle can turn. The cylinder is also the most important part of your door lock because it carries out the function that locks were made to do - protecting your family, you and your belongings. Rekeying locks is a more cost-effective alternative to replacing upvc door lock mechanism lock on upvc door lock replacements door (Botdb writes) them.

The replacement lock for composite door of locks is more difficult than simply swapping out the existing deadbolt or handle lock. Changing the entire lock requires removal of the old cylinder as well as hardware from the door (including the handle when you have a knob lock combo) and installing a new one in its place. While there are a number of DIY-friendly tools that can be used to change a lock yourself however, it is recommended you speak with a professional locksmith to make sure the job is done right.

Before you install an entirely new lock and cylinder, it is important to have the right key for your house. A key that is duplicate will not work properly and could cause the lock to fail completely, rendering it impossible to open. A professional can help prevent this from happening by making sure you have a an actual, working key for your house.

The next step is to remove the faceplate, then the latch plate. You will require an screwdriver to take out the screws which hold them in place. If the new plates are going to be identical to the original ones, you may wish to hold them in place to speed up the process. If you have to replace them, don't overtighten screws, as this can reduce their grip.

After taking off the plates, you will have to determine the proper measurement to determine the proper size of the lock. While many contemporary locksets will be able to fit a standard width of door, it is best to know the dimensions of your door in advance to avoid frustration when you arrive at the hardware store. Doorknob locksets are often different sizes than deadbolt locks and commercial models may come with a larger latch or bolt.